#Genie intellicode keypad code

#Genie intellicode keypad code

Enter your PIN number after pressing the Learn Code button described above, while the motor head indicator light is blinking.When pressed, a radio signal indicator will start blinking red for 30 seconds. This small black button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the power head. Gently press and release the Receiver Learn Code button on the Power Head Receiver of your Genie Garage Door Opener (Genie motor on the ceiling). To access, press inward, under the number pad lip while sliding downward to expose the battery. Check the 9 volt battery under the keypad numbers. Note: if red indicator light does not blink, it is not taking the programming steps.

Enter your Personal Identification Number (PIN).

Open cover fully by sliding keypad cover up until it latches.

To Program the Intellicode Wireless Keypad Indicator light will blink once and go out.

Press and hold “PROG” and “8” while fully opening cover.

GWKIC, ACSDG, Two Part, Step-By-Step Programming Model 1: Intellicode Model GWKIC, ACSDG ( black with slide-up cover and the word “Intellicode” printed on the cover) Genie Wireless Intellicode Keyless Entry Pad Programming: 3 Models

Test Keypad by sliding cover up until it latches.

Enter Door Code, as determined from the chart above, and press the “star” key.

Your PIN number can be created from any group of numbers up to 8 digits of your choice.

Enter your PIN and press the # button.

Press 3, 5, 7 and # buttons in said order.

If the back lit keypad light goes out, close the cover pad and reopen it until it clicks. At this point, if the back lit keypad light stays on, proceed directly to step 2. While pressing the # and 8 buttons simultaneously, slide the Keypad Cover the rest of the way up until it latches.

Reset Keypad–slide keypad cover half way up.

You can then print out a legible copy of the chart and the programming instructions from your word software. To make a copy, highlight area and copy into your word program. You should have 3 or 4 Door Code numbers. Continue with the next 3 switches and its corresponding number, and so on, until the last set of 3 switches. Determine the settings of the first 3 switches and write down the corresponding number from the chart. The Door Code in the Step-By-Step Procedure at right is determined by the internal code switches inside your transmitter and the accompanying chart. It is NOT compatible with Genie Intellicode transmitters (if your keypad has Intellicode printed on the cover, go to the next set of programming instructions below). This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. Keypad is black with a slide-up cover showing the Genie logo only) ( works with remotes having 9 or 12 internal code setting switches. Outside Keypad Programming Genie Garage Door Opener Keypads Genie Garage Door Opener Wireless Keypad Model GPWK-12, GWK

Gadgets & Miscellaneous Garage Door Opener Parts.

Liftmaster / Chamberlain Outside Touchpads.

Sears / Craftsman Compatible Miscellaneous Parts.

Sears / Craftsman Compatible Infra-Red Sensors.

Sears / Craftsman Compatible Outside Keypads.

Sears / Craftsman Compatible Remote Controls.

Liftmaster / Chamberlain Miscellaneous Parts.

Liftmaster / Chamberlain Infra-Red Sensors.Liftmaster / Chamberlain Outside Keypads.Liftmaster / Chamberlain Remote Controls.The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. The cookie is used to store the user consent for the cookies in the category 'Performance'. This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category 'Other. The cookies is used to store the user consent for the cookies in the category 'Necessary'. The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category 'Functional'. The cookie is used to store the user consent for the cookies in the category 'Analytics'. These cookies ensure basic functionalities and security features of the website, anonymously. Necessary cookies are absolutely essential for the website to function properly.